Document Reference No.: FT_000367
UM232H Single Channel USB Hi-Speed FT232H Development Module Error!
Unknown document property name.
Datasheet Version 1.3
Clearance No.: FTDI# 198
4.3 ACBUS Signal Options
The table below describes the EEPROM options which can be configured on the ACBUS I/O pins using the
software utility FT_PROG (which can be downloaded from the FTDI utilities page) The default EEPROM
configuration is described in section 9.
ACBUS Signal
Option
TXDEN
*PWREN#
TXLED#
RXLED#
TX&RXLED#
SLEEP#
**CLK30
**CLK15
**CLK7.5
TriSt-PU
DRIVE 1
DRIVE 0
I/O mode
Available On ACBUS Pin
ACBUS0, ACBUS1, ACBUS2, ACBUS3,
ACBUS4, ACBUS5, ACBUS6, ACBUS8,
ACBUS9
ACBUS0, ACBUS1, ACBUS2, ACBUS3,
ACBUS4, ACBUS5, ACBUS6, ACBUS8,
ACBUS9
ACBUS0, ACBUS1, ACBUS2, ACBUS3,
ACBUS4, ACBUS5, ACBUS6, ACBUS8,
ACBUS9
ACBUS0, ACBUS1, ACBUS2, ACBUS3,
ACBUS4, ACBUS5, ACBUS6, ACBUS8,
ACBUS9
ACBUS0, ACBUS1, ACBUS2, ACBUS3,
ACBUS4, ACBUS5, ACBUS6, ACBUS8,
ACBUS9
ACBUS0, ACBUS1, ACBUS2, ACBUS3,
ACBUS4, ACBUS5, ACBUS6, ACBUS8,
ACBUS9
ACBUS0, ACBUS5, ACBUS6,ACBUS8,
ACBUS9
ACBUS0, ACBUS5, ACBUS6,ACBUS8,
ACBUS9
ACBUS0, ACBUS5, ACBUS6,ACBUS8,
ACBUS9
ACBUS0, ACBUS1, ACBUS2, ACBUS3,
ACBUS4, ACBUS5, ACBUS6, ACBUS8,
ACBUS9
ACBUS0, ACBUS5, ACBUS6,ACBUS8,
ACBUS9
ACBUS0, ACBUS1, ACBUS2, ACBUS3,
ACBUS4, ACBUS5, ACBUS6, ACBUS8,
ACBUS9
ACBUS5, ACBUS6,ACBUS8, ACBUS9
Description
TXDEN = (TTL level). Used with RS485 level converters to
enable the line driver during data transmit. TXDEN is
active from one-bit time before the start bit is transmitted
on TXD until one bit time after the last stop bit.
Output is low after the device has been configured by
USB, then high during USB suspend mode. This output can
be used to control power to external logic P-Channel logic
level MOSFET switch. Enable the interface pull-down
option when using the PWREN# in this way.*
TXLED = Transmit signalling output. Pulses low when
transmitting data (TXD) to the external device. This can
be connected to an LED.
RXLED = Receive signalling output. Pulses low when
receiving data (RXD) from the external device. This can be
connected to an LED.
LED drive – pulses low when transmitting or receiving data
from or to the external device. For more details, refer to
the FT232H datasheet on the FTDI website .
Goes low during USB suspend mode. Typically used to
power down an external TTL to RS232 level converter IC
in USB to RS232 converter designs.
30MHz Clock output.
15MHz Clock output.
7.5MHz Clock output.
Input Pull Up
Output High
Output Low
ACBUS BitBang
Table 4.4 : ACBUS Signal Option
* A 10kΩ resistor pull up is also recommended.
**When in USB suspend mode, the output clocks are also suspended.
13
? Copyright 2012 Future Technology Devices International Ltd
相关PDF资料
UM232R MOD USB UART DEV FT232R
UM245R MOD USB PARALLEL FIFO DEV FT245R
UMTS 2 FUSE 2A 250V TLAG IEC SMD
UPG1-4-61-303-01 MAGNETIC CIRC BRKR SP 30A TOG SW
UPL111-1-60-503 MAGNETIC CIRCUIT PROTECTOR 50A
UPL2000-D1/B BNC PLUG CRIMP STR 7538CBL 50/PK
UPL2000-D20/B BNC PLUG CRIMP STR 1505F 50/PK
UPL220-009 BNC PLUG FULL CRIMP STR 8218CBL
相关代理商/技术参数
UM232H-B 制造商:Future Technology Devices International (FTDI Chip) 功能描述:BRD BREAKOUT USB HS FT232H 制造商:Future Technology Devices International (FTDI Chip) 功能描述:Development Module for FT232H with a Female Connector
UM232H-B-01 功能描述:界面开发工具 USB to Serial/Paral. Break-out Board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V
UM232H-B-NC 功能描述:界面开发工具 USB to Serial/Paral. Break Out Board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V
UM232H-B-WE 功能描述:界面开发工具 USB to Serial/Paral. Break Out Board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V
UM232M 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC
UM232R 功能描述:界面开发工具 USB to Serial UART Dev Mod for FT232R RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V
UM233 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC
UM233M 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC